Forum Replies Created

Viewing 11 posts - 1 through 11 (of 11 total)
  • gregkrak
    Posts: 26
    June 2, 2011 at 7:37 am #970409

    I have chosen a good transmitter.
    Do I understand that I have to reduce the speed of scrolling (scroll speed)?

    gregkrak
    Posts: 26
    May 29, 2011 at 5:31 pm #969783

    At 200 hz can not see curves (^) on the frequency of fish and 83 are visible.
    Why does the 200 do not see them but only some spots?

    Why is there no such shapes in 200 hz fish that are at 83?
    Of the 83 visible arches (^) and the 200-none – shows me why?

    gregkrak
    Posts: 26
    May 12, 2011 at 6:42 am #965474

    moreyes, thanks for your help!
    Is anyone else can give me advice on how to set structurescan shallow water up to 10 meters?

    gregkrak
    Posts: 26
    May 8, 2011 at 4:08 pm #964276

    I installed 4.0.

    I do not know how to use HDS and LSS.

    Please link to a video with the manual and answer on transducers

    Looking for a good sonar transducer to the HDS-8, what do you think (if this will be good) to Airmar P66?

    What can you recommend?

    please write the model and why this is the best.

    Thank you very much for your help!

    gregkrak
    Posts: 26
    March 6, 2011 at 5:35 pm #944515

    HDS-8 slots (slot) card?
    Hi,
    I have a question about the socket (slot) cards in the HDS-8.
    There are two slots (slots), and differ in that when one is “+”

    (I got there, two slots (slots), different “+”
    Which slot is to record data from HDS?
    (where you insert the card to record data from hds)
    What does this “+”?

    gregkrak
    Posts: 26
    March 3, 2011 at 6:02 pm #943599

    Sorry but I still have problems to understand the (not quite understand)

    Can you draw me to (describe exactly) how to connect the hds and lss-1 so I can switch (button) run (enable) lss-1 when I want.

    Will option B is so run (option B will be run) with a switch (switch) scan structure (LSS-1)?

    As the connecting pins (wires) to the battery is to enable (start) hds (automatic and switch start (activate) scan structure (LSS-1) when I want (I want it)

    Sonar HDS is to run as connecting to the battery and when I press the LSS (run) switch

    gregkrak
    Posts: 26
    March 3, 2011 at 5:36 pm #943588

    Option B – that will be fine? (ok?)

    I do not understand too well (I do not know too many) into English so please forgive me (remember this) that they do not understand everything (I do not read carefully)

    Is this good?

    gregkrak
    Posts: 26
    March 3, 2011 at 4:27 pm #943528

    Thanks for the replies!
    Is this right?
    (Will it be good?)

    I’ll be able to switch turn on (start) LSS-1?
    Thank you very much again for your help and look forward to your reply !

    gregkrak
    Posts: 26
    February 26, 2011 at 3:43 am #941679

    Thank you for your help!
    One more question if the card is to be SD or SDHC?

    gregkrak
    Posts: 26
    February 22, 2011 at 12:04 pm #940257

    I want to buy gel battery but i don’t know how many Ah should have and it can’t be one or it’s should be one for HDS and one for LSS-1.

    gregkrak
    Posts: 26
    February 21, 2011 at 11:16 am #939813

    Thanks for answer but i have one more question i read somewhere that distance between LSS-1 Transducer and 2D Transducer should be max 300 mm min 30 mm. Can someone confirm that ?

    Do you have maybe diagram with all installation from battery to each unit or do you know from where i can download or check that ?

Viewing 11 posts - 1 through 11 (of 11 total)