The new boat w/ cover pics

  • skeeter20
    Winnie/Grand Rapids,MN
    Posts: 902
    May 18, 2011 at 1:09 pm #1320144

    Well I promised I would post pics when the cover was done with both motors covered all in one piece so here is it! I am very happy with how it turned out. There is another pole in the front and rear that I didnt have in but it trailered just fine with the one.

    As for the boat…It was awesome fishing out of on opener. Everything worked great and I love the extra room in the back with the livewells no longer coming up the side. Used cruise control on the Ipilot which was slick! The performance was also good for the prop not being done yet. 3 people, 1/2 tank fuel and all 3 wells filled up I ran 59.5mph. By myself going with a 5-10mph wind I hit 61.7.

    This weekend I am going to add some 3M clear tape like they use on cars to the rear of the boat where the motor hose is, kicker handle and then a small piece on the big motor just incase it were to hit the kicker. Also adding some non slip pads on the deck in front and rear.

    Cant wait to get back to the lake on Friday and do some more fishing



    skeeter20
    Winnie/Grand Rapids,MN
    Posts: 902
    May 18, 2011 at 1:34 pm #966794

    Thanks Wade, when do you get yours?

    Wade Boardman
    Grand Rapids, MN
    Posts: 4453
    May 18, 2011 at 1:37 pm #966796

    It will be at SBC either Friday or Monday. I’m about to a point I can’t sit still. I should pick it up mid-week or that weekend.

    skeeter20
    Winnie/Grand Rapids,MN
    Posts: 902
    May 18, 2011 at 1:44 pm #966800

    Awesome Just in time for Memorial!

    francisco4
    Holmen, WI
    Posts: 3607
    May 18, 2011 at 1:53 pm #966810

    Is it a snap on cover?

    FDR

    skeeter20
    Winnie/Grand Rapids,MN
    Posts: 902
    May 18, 2011 at 2:16 pm #966828

    Quote:

    Is it a snap on cover?

    FDR

    Yes it is a snap. I had them put the buttons this time a little lower, pretty much the bottom side of the bumper so people dont get hooked on them and if the boat were to bump the dock it wont ruin the buttons.

    James Holst
    Keymaster
    SE Minnesota
    Posts: 18926
    May 18, 2011 at 2:25 pm #966836

    Very nice, Corey. Where did you have it done?

    skeeter20
    Winnie/Grand Rapids,MN
    Posts: 902
    May 18, 2011 at 2:34 pm #966840

    Quote:

    Very nice, Corey. Where did you have it done?

    Canvas Craft in Ramsey,MN. We have probably had 10 covers made from them over the years and they all have been great.

    kroger3
    blaine mn
    Posts: 1116
    May 18, 2011 at 2:42 pm #966842

    need lower unit covers made! if I remember right there is a guy in the north metro that makes them, or atleast did. no one ever seems to like to protect the most important part….

    James Holst
    Keymaster
    SE Minnesota
    Posts: 18926
    May 18, 2011 at 2:42 pm #966844

    Quote:

    Quote:

    Very nice, Corey. Where did you have it done?

    Canvas Craft in Ramsey,MN. We have probably had 10 covers made from them over the years and they all have been great.

    I’ve heard from others of their work many, many times. Never a bad review!

    Kdawg1966
    Posts: 55
    May 18, 2011 at 5:53 pm #966923

    Super sharp boat. If you’re up on Winnie this coming week/weekend, I’ll keep an eye out for ya. Mine’s a black top, gold/beige 1850.

    Fife
    Ramsey, MN
    Posts: 4054
    May 18, 2011 at 6:16 pm #966933

    Quote:

    Super sharp boat. If you’re up on Winnie this coming week/weekend, I’ll keep an eye out for ya. Mine’s a black top, gold/beige 1850.

    See ya up there! I’m leaving tomorrow afternoon for a 3 day weekend.

    skeeter20
    Winnie/Grand Rapids,MN
    Posts: 902
    May 18, 2011 at 6:24 pm #966937

    Quote:

    Quote:

    Super sharp boat. If you’re up on Winnie this coming week/weekend, I’ll keep an eye out for ya. Mine’s a black top, gold/beige 1850.

    See ya up there! I’m leaving tomorrow afternoon for a 3 day weekend.

    I should be up there around 3pm friday! Might make it out but if not sat & sun for sure. Good Luck guys!

    suzuki
    Woodbury, Mn
    Posts: 18715
    May 18, 2011 at 9:41 pm #966996

    Possibly some air shocks for the truck?

    mike-g
    Bloomington,MN
    Posts: 556
    May 18, 2011 at 10:00 pm #966999

    Good lookin’ cover Corey.

    eyehabit
    WestBend Wisconsin
    Posts: 64
    May 19, 2011 at 1:43 am #967041

    very nice boat

    skeeter20
    Winnie/Grand Rapids,MN
    Posts: 902
    May 19, 2011 at 2:32 am #967056

    Quote:

    Possibly some air shocks for the truck?

    Nope its already got an sst lift. Truck does sit pretty much level I am just on a pretty big incline there.

    skeeter20
    Winnie/Grand Rapids,MN
    Posts: 902
    May 19, 2011 at 2:49 am #967064

    Quote:

    Good lookin’ cover Corey.

    Thanks Mike, I figured I better get come pics up so you could see it.

    arklite881south
    Posts: 5660
    May 19, 2011 at 12:05 pm #967111

    Looks Great!! I added the snap cover also. VERY COOL!!

    suzuki
    Woodbury, Mn
    Posts: 18715
    May 19, 2011 at 1:15 pm #967128

    Quote:

    Quote:

    Possibly some air shocks for the truck?

    Nope its already got an sst lift. Truck does sit pretty much level I am just on a pretty big incline there.

    Yea, like I was looking at the truck anyhow. Nice boat!

    skeeter20
    Winnie/Grand Rapids,MN
    Posts: 902
    May 19, 2011 at 1:20 pm #967130

    Quote:

    Quote:

    Quote:

    Possibly some air shocks for the truck?

    Nope its already got an sst lift. Truck does sit pretty much level I am just on a pretty big incline there.

    Yea, like I was looking at the truck anyhow. Nice boat!

    thanks

Viewing 27 posts - 1 through 27 (of 27 total)

You must be logged in to reply to this topic.