Lowrance problems

  • walleye1274
    Chippewa Falls, WI
    Posts: 515
    June 1, 2010 at 2:08 pm #1306656

    I have a 1.5 yr old LCX-37C unit that I am having some issues with. My depth reading are terrible. It will read depth for a minute or 2 and then it will fill with colors and flash 1.5ft deep. It does this at all depths and all speeds, even when sitting still. Then it will work again for a couple seconds. I am assuming it is a bad transducer. Does that sound correct to you?

    bclii
    MN/AZ
    Posts: 494
    June 1, 2010 at 2:21 pm #876316

    Yep, it is the transducer. They have made improvements this past year to fix this on going problem.

    jt_fish
    Posts: 138
    June 1, 2010 at 2:36 pm #876397

    Yes- Transducer. I had the same problem with a unit that was less than a year old.

    walleye1274
    Chippewa Falls, WI
    Posts: 515
    June 1, 2010 at 2:49 pm #876402

    Thanks everyone!! Any suggestions were to buy so I do not get any old stock. I would hate to get a new on and get the old style one again!!

    AllenW
    Mpls, MN
    Posts: 2895
    June 1, 2010 at 7:56 pm #876540

    OK..after a bit of a wait I got David on the Lowrance tech line.
    He says these two transducers should be the newer model units.
    Either will work on a LCX27C, not sure for other models though.

    Model: HST-WSBL
    PART NUMBER 106-72
    and

    Model HST-DFSBL
    Part number 106-77

    There are as accurate as I could be, but please check with Lowrance before you buy them or maybe some one on the forum would/could verify these transducers are correct.

    Al

    walleye1274
    Chippewa Falls, WI
    Posts: 515
    June 1, 2010 at 8:36 pm #876561

    Thanks Allen, I have one on it’s way from Wade. Really hope it takes care of the problem!!

    AllenW
    Mpls, MN
    Posts: 2895
    June 1, 2010 at 11:07 pm #876597

    Quote:

    Thanks Allen, I have one on it’s way from Wade. Really hope it takes care of the problem!!

    Did he happen to know for sure if these are the newer models?
    Which one did you get if I may ask?

    Al

    walleye1274
    Chippewa Falls, WI
    Posts: 515
    June 2, 2010 at 12:46 am #876616

    Model: HST-WSBL
    PART NUMBER 106-72

    Wade figured that this should be of new stock. Sounds like they have been hard to keep in stock for some places.

    AllenW
    Mpls, MN
    Posts: 2895
    June 2, 2010 at 12:53 am #876620

    Thanks, hoping someplace locally has it but I may just email him tomm.

    Al

    topdawg1817
    Posts: 29
    June 3, 2010 at 7:39 pm #877111

    I just started having the same issue with my 2.5 yr old X510C. Sounds like I need to go and invest in a a new ducer to hopefully fix the problem. It’s always fun when your out fishing and your equipment takes a poop on you.

    AllenW
    Mpls, MN
    Posts: 2895
    June 4, 2010 at 1:34 am #877192

    Quote:

    I just started having the same issue with my 2.5 yr old X510C. Sounds like I need to go and invest in a a new ducer to hopefully fix the problem. It’s always fun when your out fishing and your equipment takes a poop on you.

    If your near Blaine, Thorne Bros has the HST-WSBL in stock

    Al

    walleye1274
    Chippewa Falls, WI
    Posts: 515
    June 7, 2010 at 1:27 am #877742

    Installed the new transducer this morning, and all is good again. I think it had been acting up for quite some time, because it is reading great now.

Viewing 12 posts - 1 through 12 (of 12 total)

You must be logged in to reply to this topic.