STRIKEMASTER MAG 2000

  • bullcans
    Northfield MN
    Posts: 2012
    February 5, 2013 at 4:20 pm #1305079

    Can someone tell me what the oil-gas mixture ratio is please?

    Chuck Melcher
    SE Wisconsin, Racine County
    Posts: 1966
    February 5, 2013 at 4:32 pm #1138320

    Going to depend on the oil.

    I run a synthetic I have left over from my motorcycle racing days at 50 to 1. Oils often range from 20-1 to 100-1. I think you will here guys tend to run them a little on the lean side of an oil’s recommended mix range.

    jigawhopper
    Ellsworth,WI
    Posts: 8
    February 5, 2013 at 4:32 pm #1138321

    Mine must be 8 – 10 years old with a Tecumseh engine and it’s listed at 24:1.

    chappy
    Hastings, MN
    Posts: 4854
    February 5, 2013 at 4:46 pm #1138324

    x2

    Huntindave
    Shell Rock Iowa
    Posts: 3092
    February 5, 2013 at 5:15 pm #1138333

    Quote:

    Can someone tell me what the oil-gas mixture ratio is please?

    24 to 1

    You do not want to run this engine any leaner. It was designed to run at 24 to 1 and changing brands or types of oil will not change the engine requirements.

    timschmitz
    Waconia MN
    Posts: 1652
    February 5, 2013 at 5:27 pm #1138341

    Quote:

    Quote:

    Can someone tell me what the oil-gas mixture ratio is please?

    24 to 1

    You do not want to run this engine any leaner. It was designed to run at 24 to 1 and changing brands or types of oil will not change the engine requirements.

    Haha! That’s funny!! My solo says to run at 40:1 but at that mix it burps oil and smokes like a chimney. I run it at 100:1 with amisoil saber with zero issues. Pick up some amisoil and run her lean!

    ajs
    Mellen,WI
    Posts: 248
    February 5, 2013 at 5:46 pm #1138346

    Run it at 50 to 1 and you will be fine. the old tecumsehs say 24 to 1 but i have never seen any issues at 50 to 1. And i also run my solo at 50 to 1 with no troubles.

    Ajs

    Chuck Melcher
    SE Wisconsin, Racine County
    Posts: 1966
    February 5, 2013 at 5:52 pm #1138349

    Do not just run any oil at 24-1.

    Mine also says 24-1, and while that is fine for some oils – others will foul and run like garbage that rich. It really is all about what oil you are using. Go to a local store and get a decent oil, read the bottle. If it is a 20-1 oil (most likely mineral based) then run your 24-1 and you are good to go. Synthetic oils for the most part will be 32-1 to 100-1… using the manufacturer’s recommendation. Oil I use is 32-1 to 50-1… I have ran 50-1 for years and it is perfect.

    A average sized bottle will last you a long time…. and mixed right, you can use it for weed wackers, blowers or whatever so it doesn’t sit too long. Add a stabilizer, and mix as little as possible at a time to keep it fresh.

    phishirman
    Madison, WI
    Posts: 1090
    February 5, 2013 at 6:23 pm #1138362

    Run it at 50 to 1 and you will be fine. the old tecumsehs say 24 to 1 but i have never seen any issues at 50 to 1.

    x2

    Joe Scegura
    Alexandria MN
    Posts: 2758
    February 5, 2013 at 6:43 pm #1138371

    Straight from Strikemaster… run the older tecumsehs at 40:1. The auger says 24:1, but Strikemaster says that’s too rich.

    tmyboy2001
    Lakeville, MN
    Posts: 282
    February 5, 2013 at 7:10 pm #1138384

    X2. I have an ’07 Mag 2000 that I run at 40:1, per D-Rock and hasn’t given me any issues. Smokes more than I’d like it to, but it fires right up and runs flawlessly.

    out_fishing
    Moorhead, MN
    Posts: 1151
    February 5, 2013 at 7:56 pm #1138405

    Quote:

    Straight from Strikemaster… run the older tecumsehs at 40:1. The auger says 24:1, but Strikemaster says that’s too rich.

    X2 – I just buy the strikemaster oil that you mix with a gallon of gas. I believe its 40-1.

Viewing 12 posts - 1 through 12 (of 12 total)

You must be logged in to reply to this topic.